Thermal Power Plant (Boiler Parts)

Boiler :
Boiler is a steam generator which is used to generate super heated steam to rotate the turbine. There are many type of boiler according to their use, but we concentrate on modern boiler used in high capacity thermal power plant.

In modern power plant mainly pulverized fuel fired boilers are working.

Type of boiler according to fire location :
1. Corner fired boiler ( BHEL make this type of boiler)
2. Front and rear fired boiler (ABB Make)

Main parts of a pulverized fuel boiler ;-
6. Final Super Heater
7. Radiant Super Heater
8. Re heater
9. Steam cooled wall
10. Air Pre heater

A schematic diagram of a 210 MW boiler is showing in fig. 
Power plant boiler - 1
For more details click on below link :
http://blog.mechanicsoflife.in/2016/03/boiler-parts.html

Comments

Post a Comment

Popular posts from this blog

Introduction to Thermal Power Plant

Image
INTRODUCTION TO THERMAL POWER PLANT: The thermal power plant are coal based power plants. It uses coal as a fuel to generate steam from water in its boiler. There is a closed cycle to enable the working fluid (water) to be used again and again. The cycle used in steam power plant is “Rankine Reheat and Regenerative cycle (modified Rankine cycle).  The figure shows this cycle and is self explanatory. Simple power plant steam water cycle  Rankine Reheat and Regenerative Cycle [2] On large turbines, it becomes economical to increase the cycle efficiency  by using reheat, by returning partially expanded steam, to a reheater, the average temperature at which heat is added, is increased and, by expanding this reheated steam to the remaining stages of the turbine, the exhaust wetness is considerably less than it would otherwise be conversely. Regenerative heating of the boiler feed water is widely used in modern Power plants; the effect being to increase the average temperatu...
Read more

Boiler Parts (Platen Super Heater)

Image
Platen super heater or pendent super heater (PSH) Platen Super heaters are placed just above the goose neck. the flue gases leaving the furnace transfer heat at first to platen super heater. The super heated steam from LTSH outlet header goes to platen SH inlet header and again take sensible heat from flue gas by running throug h PSH coil. The coil of this SH are hanging type and comes in first pass (furnace side) of boiler. In a 210 MW boiler there are 29 coils having 26 loop tube with 51 mm dia and different thickness as 4.5/5.6/7.1/8.8/10 mm are used to make platen super heater. There is an arrangement between PSH and final SH called as attemperation to control the final temperature of super heated steam. all headers are lying in Top and sealed space of Boiler Furnace named as Pent House.
Read more

इंजीनियरिंग मैकेनिक्स एंड मैकेनिक्स ऑफ़ लाइफ

Image
इंजीनियरिंग मैकेनिक्स एंड मैकेनिक्स ऑफ़ लाइफ  (अभियान्त्रिकी एवं जिंदगी की यांत्रिकी  ) यांत्रिकी   Mechanics यांत्रिकी भौतिक शास्त्र की एक शाखा है, जो बल एवं उसके किसी वस्तु या कण पर पड़ने वाले प्रभाव, या कण के  द्रव्यमान, जड़त्व,गति आदि का अध्ययन  करती है। ( कण उस वस्तु को माना जाता है जिसका द्रव्यमान नगण्य हो, या ऐसा कहे कि उस वस्तु पर लगने वाले बाह्य बालो की तुलना में वस्तु का भार नगण्य हो। ) यह यांत्रिकी की एक सरल परिभाषा है हम इसमें कुछ और भी जोड़ सकते है। जैसा कि यह बल एवं उसके प्रभाव से संबंधित है; हम इसके सिद्धान्तो को जिंदगी से भी जोड़ सकते है, क्युकि दैनिक जीवन में भी कई बाहरी चीजो का प्रभाव पड़ता है।  जैसे नौकरी, परिवार, सम्बन्ध, पैसा, दोस्ती, तनाव, ख़ुशी, आदि। मैंने इसे एक नाम देना उचित समझा   "जिंदगी की यांत्रिकी " (मैकेनिक्स ऑफ़ लाइफ ) सबसे पहले हम यांत्रिकी के सिद्धांतो को समझेंगे फिर उन्हें जिंदगी पर लागु कर के देखेंगे। बलो के संतुलन के प्रश्नो को हल कीजिये फिर उन्हें सम्बन्धो एवं नौकरी / व्यवस...
Read more