Posts

Showing posts with the label thermal power plant

Boiler Parts (Super Heater)

Image
Super Heater Generally super heaters are used in boiler to increase the temperature of a saturated steam comes from boiler drum. In boiler drum as discuss in earlier blogs number of turbo (Cyclone) separators are working to separate saturated steam and water, water goes to water wall again and again to receive saturated steam condition, this saturated steam now goes to achieve super-heated temperature generally 540 0 in a 210 MW capacity boiler by heat transfer from flue gases. The super heaters are classified by their location and temperature range. The steam transfer takes place gradually. The location of super heater decided in such a manner that temperature difference between steam and flue gases occurs not to high. i.e the temperature of flue gases at low temperature super heater is less then temperature at final super heater. in a 210 MW boiler there are three super heaters are generally used : Low temperature super heater (LTSH) or Primary super heater Platen super heater...

Boilers Part (Economizer)

Image
Economizer: The purpose of  economizer  is to preheat the boiler feed water before it is introduced into the steam drum by recovering heat from the flue gases leaving the boiler. The  economizer  is located in the boiler rear gas pass (second pass) below the Low Temperature S uperheater . The  economizer  is a continuous loop of tubes (coil) and water flows in upward direction and gas in the downward direction.[1]  The function of an  economizer  in a steam generating unit is to absorb heat from the flue gases and add this as sensible heat to the feed water before the water enters the evaporative circuit of the boiler. Earlier the economizers were introduced mainly to recover the heat available in flue gas that leaves the boiler and provision of the additional heating surface increased the efficiency of steam generation, saving the fuel consumption, thus the name is ‘Economizer’. In modern boilers power generation feed wat...

Thermal Power Plant (Material Used in Boiler and color code for H.P.Tube material)

Material used for boiler tubes To improve the properties of iron, suitable elements are added to it such as chromium, Nickel etc to suit the condition of boiler.              Alloying elements can be broadly classified in to two groups a)      Austenite stabilisers :- Which have the effect of extending the temperature rang over which austenite is formed. Such elements are :             Carbon             Manganese             Nickel             Copper             Cobalt b) Ferrite stabilisers :- Which have the effect of extending the temperature range over which alpha & delta ferrite are formed, which consequently reduces temperat...

BOILER PARTS (Water wall and Drum)

Image
Boiler Parts : Water walls Almost all modern power boilers are equipped with water walls. In large boilers, water walls completely cover the interior surfaces of the furnace providing practically complete elimination of exposed refractory surface; Waterwalls serve as the only means of heating and evaporating the feed water supplied to the boiler from  economizers . Waterwalls usually consists of tangential vertical tubes and are connected at the top and bottom to headers. These tubes receive water from the boiler drum by means of downcomers connected between drum and Waterwalls lower header (Bottom Ring Header). In a boiler approximately 50% of the heat released by combustion of fuel in the furnace is  absorbed  by Waterwalls. Heat so absorbed by the Waterwalls is used in evaporation of water supplied to the boiler. The evaporated steam supplied to Boiler Drum again by mean of riser tubes from top header of water wall. W/W Top Header water wall of a thermal powe...

Thermal Power Plant (Boiler Parts)

Image
Boiler : Boiler is a steam generator which is used to generate super heated steam to rotate the turbine. There are many type of boiler according to their use, but we concentrate on modern boiler used in high capacity thermal power plant. In modern power plant mainly pulverized fuel fired boilers are working. Type of boiler according to fire location : 1. Corner fired boiler ( BHEL make this type of boiler) 2. Front and rear fired boiler (ABB Make) Main parts of a pulverized fuel boiler ;- 1. Water wall 2. Boiler Drum 3. Economizer 4. Primary or Low Temperature Super Heater ( LTSH) 5. Platen super Heater 6. Final Super Heater 7. Radiant Super Heater 8. Re heater 9. Steam cooled wall 10. Air Pre heater A schematic diagram of a 210 MW boiler is showing in fig.  Power plant boiler - 1 For more details click on below link : http://blog.mechanicsoflife.in/2016/03/boiler-parts.html

Introduction to Thermal Power Plant

Image
INTRODUCTION TO THERMAL POWER PLANT: The thermal power plant are coal based power plants. It uses coal as a fuel to generate steam from water in its boiler. There is a closed cycle to enable the working fluid (water) to be used again and again. The cycle used in steam power plant is “Rankine Reheat and Regenerative cycle (modified Rankine cycle).  The figure shows this cycle and is self explanatory. Simple power plant steam water cycle  Rankine Reheat and Regenerative Cycle [2] On large turbines, it becomes economical to increase the cycle efficiency  by using reheat, by returning partially expanded steam, to a reheater, the average temperature at which heat is added, is increased and, by expanding this reheated steam to the remaining stages of the turbine, the exhaust wetness is considerably less than it would otherwise be conversely. Regenerative heating of the boiler feed water is widely used in modern Power plants; the effect being to increase the average temperatu...